loading
Availability: | |
---|---|
Quantity: | |
TM-GD01
Transmei
25g
ø85X30mm
white
ABS
500
Real-time detection of natural gas leakage status, the day the gas leakage reaches the alarm threshold, on-site alarm, and the alarm information is transmitted to the user's mobile phone at the same time.
Communication Mode | ZigBee |
Dimension | ø85X30mm |
Operating Temperature | -10~55℃ |
Power Supply | DC 12V, external adapter |
Material | Fireproof PC+ Fireproof ABS |
Installation | Bracket |
Alarm density | 8%LEL±3%LEL |
Density tolerrance: | ±3%LEL |
Alarm sound pressure: | ≥70dB(1m ahead) |
Real-time detection of natural gas leakage status, the day the gas leakage reaches the alarm threshold, on-site alarm, and the alarm information is transmitted to the user's mobile phone at the same time.
Communication Mode | ZigBee |
Dimension | ø85X30mm |
Operating Temperature | -10~55℃ |
Power Supply | DC 12V, external adapter |
Material | Fireproof PC+ Fireproof ABS |
Installation | Bracket |
Alarm density | 8%LEL±3%LEL |
Density tolerrance: | ±3%LEL |
Alarm sound pressure: | ≥70dB(1m ahead) |
Using gas sensor, high sensitivity and stable operation On-site alarm, more than 70dB
Accurate detection 8%, density alarm Temperature
compensation function
Send status report to the gateway periodically
Indicator and Buzzer States
Network settings
1. After turning on, the detector will warm up for 1-3 minutes and the yellow LED will flash.
2. Press and release the reset button 5S, the green LED indicator will flash for network settings.
Distribution network tips:
Press the reset button for 5s-10s, the red LED lights up, and when the reset button is released, the green LED flashes for network settings. The green LED indicator will light up for 5 seconds, and then turn off to indicate that the network setting is successful and the product is in the network detection state.
If the network setting fails within 20 seconds, the yellow LED lights up for 5 seconds, then turns off, and then the green LED lights up, and the product is in an independent working state.
Installation Instructions
1. Precautions
(1) Install the product in the room where the equipment uses combustible materials Gas (methane).
(2) Do not install the product outdoors.
(3) Ensure the installation ambient temperature In the range of ‒10°C to +55°C.
(4) Do not install this product where it is to be placed.Influenced by heat generated by gas appliances, steam or smoke residue(For example, above the gas stove).
(5) Ensure that there are no obstacles between products.Gas equipment, otherwise the product may fail to detect gas leaks.
(6) Do not install the product in a place with high airflow, for example:
Air intakes, ventilators, doors and windows or products It may not be possible to detect a gas leak.
(7) Make sure that the product is properly connected to the power supply Outlet, and the outlet is energized.
(8) It is recommended to use screws to install the product. 3M label to install the product, any product is damaged or safe You will be responsible for the accidents caused by it, but,If you choose to use the 3M label, please paste the product on the smooth,Evenly, dry and clean the surface.
(9) Regularly check whether the product is attached to the surface
Safely prevent it from falling.
2. Installation location
Ceiling installation: Install the product in a circular area approximately 1.5 m to 3 m above the air source.
Wall-mounted: Install the product on a wall below approximately 0.2 m to 0.6 m Ceiling, 1.5 m from the air source.
3.Installation methods
Real-time detection of natural gas leakage status, the day the gas leakage reaches the alarm threshold, on-site alarm, and the alarm information is transmitted to the user's mobile phone at the same time.
Communication Mode | ZigBee |
Dimension | ø85X30mm |
Operating Temperature | -10~55℃ |
Power Supply | DC 12V, external adapter |
Material | Fireproof PC+ Fireproof ABS |
Installation | Bracket |
Alarm density | 8%LEL±3%LEL |
Density tolerrance: | ±3%LEL |
Alarm sound pressure: | ≥70dB(1m ahead) |
Using gas sensor, high sensitivity and stable operation On-site alarm, more than 70dB
Accurate detection 8%, density alarm Temperature
compensation function
Send status report to the gateway periodically
Indicator and Buzzer States
Network settings
1. After turning on, the detector will warm up for 1-3 minutes and the yellow LED will flash.
2. Press and release the reset button 5S, the green LED indicator will flash for network settings.
Distribution network tips:
Press the reset button for 5s-10s, the red LED lights up, and when the reset button is released, the green LED flashes for network settings. The green LED indicator will light up for 5 seconds, and then turn off to indicate that the network setting is successful and the product is in the network detection state.
If the network setting fails within 20 seconds, the yellow LED lights up for 5 seconds, then turns off, and then the green LED lights up, and the product is in an independent working state.
Installation Instructions
1. Precautions
(1) Install the product in the room where the equipment uses combustible materials Gas (methane).
(2) Do not install the product outdoors.
(3) Ensure the installation ambient temperature In the range of ‒10°C to +55°C.
(4) Do not install this product where it is to be placed.Influenced by heat generated by gas appliances, steam or smoke residue(For example, above the gas stove).
(5) Ensure that there are no obstacles between products.Gas equipment, otherwise the product may fail to detect gas leaks.
(6) Do not install the product in a place with high airflow, for example:
Air intakes, ventilators, doors and windows or products It may not be possible to detect a gas leak.
(7) Make sure that the product is properly connected to the power supply Outlet, and the outlet is energized.
(8) It is recommended to use screws to install the product. 3M label to install the product, any product is damaged or safe You will be responsible for the accidents caused by it, but,If you choose to use the 3M label, please paste the product on the smooth,Evenly, dry and clean the surface.
(9) Regularly check whether the product is attached to the surface
Safely prevent it from falling.
2. Installation location
Ceiling installation: Install the product in a circular area approximately 1.5 m to 3 m above the air source.
Wall-mounted: Install the product on a wall below approximately 0.2 m to 0.6 m Ceiling, 1.5 m from the air source.
3.Installation methods
Using this Product
1. The product enters the preheating state after being turned on in the preheating state.During warm-up, the status indicator flashes yellow
After preheating is completed (not more than 3 minutes),The status indicator will turn solid green.
2. Working status When the product is working normally, the status indicator will be on Steady green, no alarm sound.
3. Alarm status If the product is working properly and the gas concentration is Above the preset alarm threshold, the red indicator light flashes The buzzer will sound an audible alarm.
4. Failure status If the product fails, the yellow indicator flashes, and
The buzzer will make a long sound.
5. Press Mute/Self-diagnosis when working on simulated test products Button to enter simulation test mode.In the simulation test mode, the product will send a wireless alarm signal.After the test is completed, the product will send a wireless alert Permission signal.
Toxic or harmful substances or elements this product
Warranty Certificate
Warranty policy:
1. If the product has quality problems within 7 days after payment On the date, you can apply for a refund based on the invoice price, or you can
2. If the product has quality problems within 15 days after payment, please replace it with the same model or repair it.
Date, you can apply to replace the product with the same model or the following model Repaired.
3. If the product has quality problems within 12 months after warranty,On the payment date, you can apply for repairs.
This warranty does not include:
1. The product owner has no warranty certificate or warranty
The service has expired.
2. Damage caused by improper use, maintenance or storage.
3. Damage caused without Tuya's disassembly and repair.
Authorization
4. Damage caused by force majeure
5. The product will change color and depreciate normally after used
Using this Product
1. The product enters the preheating state after being turned on in the preheating state.During warm-up, the status indicator flashes yellow
After preheating is completed (not more than 3 minutes),The status indicator will turn solid green.
2. Working status When the product is working normally, the status indicator will be on Steady green, no alarm sound.
3. Alarm status If the product is working properly and the gas concentration is Above the preset alarm threshold, the red indicator light flashes The buzzer will sound an audible alarm.
4. Failure status If the product fails, the yellow indicator flashes, and
The buzzer will make a long sound.
5. Press Mute/Self-diagnosis when working on simulated test products Button to enter simulation test mode.In the simulation test mode, the product will send a wireless alarm signal.After the test is completed, the product will send a wireless alert Permission signal.
Toxic or harmful substances or elements this product
Warranty Certificate
Warranty policy:
1. If the product has quality problems within 7 days after payment On the date, you can apply for a refund based on the invoice price, or you can
2. If the product has quality problems within 15 days after payment, please replace it with the same model or repair it.
Date, you can apply to replace the product with the same model or the following model Repaired.
3. If the product has quality problems within 12 months after warranty,On the payment date, you can apply for repairs.
This warranty does not include:
1. The product owner has no warranty certificate or warranty
The service has expired.
2. Damage caused by improper use, maintenance or storage.
3. Damage caused without Tuya's disassembly and repair.
Authorization
4. Damage caused by force majeure
5. The product will change color and depreciate normally after used